You have two choices when it comes to remodeling your kitchen. One, you can do it yourself or hire a professional. But, if your skills are not up to par, you could end up spending more than you expected on the remodel. You should do the job right. Kitchen cabinets are an important investment in your house.
Installation of base cabinets
Installing new base cabinets for kitchen cabinets doesn't require that you hire a professional. However, you will need to have basic carpentry skills in order to do the job correctly. You must ensure that the cabinets boxes are level and straight. If not, the cabinets may not close properly or fit the appliances you plan to install in them. You will need at minimum one person to lift the cabinets and hold them in place.
Once you have settled on the layout of your base cabinets, it is time to move on to installing the upper cabinet. The upper cabinets should measure approximately 36 inches above the floor. The height of the base cabinets must not be lower than 24 inches above the countertop. Use a stud locater to mark each stud on the wall.
Installing side-by - side cabinets
Side-by-side cabinets are a complicated task that requires planning and preparation. First, measure the space and mark the layout. The old cabinets can be used as guides, or you may use a template from the design center to make a plan that is appropriate for your area.
Next align both cabinet's face frames. Secure them with C-clamps. After the cabinets have been installed, attach the next base cabinet using 2 1/2-inch #8 screws. To achieve an even look, ensure that you countersunk all screws.
Install drawer fronts
Before installing new drawer faces, you need to remove the screws that held the old drawer fronts to the drawerbox. You will need a handsaw for cutting the edges of your front panel to align it with the drawer. Next, you will need to insert screws into each hole, starting at the top hinge. Make sure you have the right length of screws
You can install the drawer fronts separately if your cabinet has them. Hardware should be installed to attach the drawer box to the front. This makes it easier to replace your front.
Checking for level
Before installing kitchen cabinets, make sure that the cabinet face meets the reference line and is parallel to the wall. If the cabinet face is not level, place shims in between the wall and cabinet. Screw the cabinet into place with two 1/2-inch screws and washers after leveling it.
A level can be used to check the level. It measures the height of the wall from the base cabinets. To measure the height on the wall adjacent to the cabinets, you can use a 2-foot ruler.
Self-drilling screws
Installing new kitchen cabinets requires self-drilling screws. Make sure the screws are the correct size. Measure the openings between the wall panels or face frames before you start. Filler strips can be added where necessary. You can add filler strips where necessary.
When using self-drilling screws, be sure to follow the manufacturer's instructions carefully. The screws typically measure two-1/2 inches in length. This allows you to embed as much as one-1/2 inches of fastener per wall panel. Brown-coated screws can also be purchased that blend with the cabinets' colors. Make sure the screws are driven flush with the rails when you drive them into the cabinet rails. The screws will now bite into the wood rail and feel as if they are a stud in wall.
Permanent blocks
It is important to plan where the block will be placed when installing kitchen cabinets. This will ensure a level surface. While the placement of block depends on the type of cabinet, there are some general rules that apply to most situations. Base cabinets must have the top of block at the top and the bottom at the bottom.
Start by measuring how high and where the cabinet is located on the wall. Then, you can drill holes in the cabinet, about 1 inch apart from the diagonal corners. Once the holes are drilled, use a socket or wrench to drive the screws in the inserts. The cabinet will then be secured to the cinderblock wall.
FAQ
Can I rent a dumpster?
To help you get rid of the debris from your home remodeling project, you can hire a dumpster. Renting a dumpster is a great way to keep your yard free from trash and debris.
Which order should you do your home renovations?
When renovating your home, the first thing to do is decide where everything should go. If you're planning on selling your home soon, it is important to consider how you wish to present your home for potential buyers. The design of your kitchen and living room should be considered. Once you have decided which rooms you want to renovate, you should start looking for contractors who specialize in those areas. After you have hired a contractor to work on your project, it is time to get started.
What time does it take to finish a home remodel?
It all depends on the project's size and how many hours you spend each week. The average homeowner works on the project for three to six hour a week.
Statistics
- The average fixed rate for a home-equity loan was recently 5.27%, and the average variable rate for a HELOC was 5.49%, according to Bankrate.com. (kiplinger.com)
- Design-builders may ask for a down payment of up to 25% or 33% of the job cost, says the NARI. (kiplinger.com)
- Most lenders will lend you up to 75% or 80% of the appraised value of your home, but some will go higher. (kiplinger.com)
- According to the National Association of the Remodeling Industry's 2019 remodeling impact report , realtors estimate that homeowners can recover 59% of the cost of a complete kitchen renovation if they sell their home. (bhg.com)
- It is advisable, however, to have a contingency of 10–20 per cent to allow for the unexpected expenses that can arise when renovating older homes. (realhomes.com)
External Links
How To
Are you renovating the exterior or interior first?
Which one should you do first?
There are many aspects to consider when choosing which project should be started. Most people consider whether the building is new or old. You should consider the condition and age of the roof, windows, doors, flooring, electric system, etc. The location, style, number of rooms and size of a new building are all important aspects.
If the building has an older roof, it is worth looking at the roof first. You might consider starting the renovation immediately if the roof appears to be in danger. If the roof is fine, then you can move onto the next step. Next, take a look at the windows. Next, inspect the windows and make sure they are clean. You can then go through your doors and clean them. If everything looks good, you can start to lay the flooring. Make sure that the flooring is solid and sturdy so that no matter how hard you walk on it, nothing breaks. These steps will be completed before you can proceed to the walls. Check the walls for cracks and damage. If the wall is intact, then you can move to the next step. The ceiling can be finished after the walls have been examined. Check the ceiling and make sure that it is strong enough to hold up whatever weight you decide to put on it. If all is well, then you are ready to move on to the next phase of your renovation.
If the building was newly built, you'd probably start with its exterior. First, examine the outside of the house. Is it well maintained? Are there cracks or holes? Does it look good overall? If it doesn't look good, you need to fix it. Your home shouldn't look shabby. Next, inspect the foundation. Repairing the foundation is a good idea if it appears weak. Also, check the driveway. You want it to be smooth and flat. If it's not, it should be fixed. You should also inspect the sidewalk while you're checking your driveway. If it's uneven, then you should probably replace it.
Once you've checked all these areas, it is time to move on the inside. Start by looking at the kitchen. Is it clean and well kept? If it is dirty or messy, you need to clean it up. Next, examine the appliances. You should make sure that they are in working order and in good condition. If they aren't, then you should either buy new ones or fix them. You can then inspect the cabinets. If the cabinets are stained, or have been scratched, you can probably paint them. If they are in good shape, then you can move to the bathroom. The toilet should be inspected here. If it leaks, then you should probably get a new one. It's best to wash it if it's only dirty. Next, examine all the fixtures. You should make sure they are clean. If they're dirty, you need to clean them. Lastly, check the countertops. You should repaint countertops that are cracked or chipped. If they are smooth and shiny, then you should probably use some kind of sealant.
Final step: Check your furniture. You should make sure nothing is broken or missing. You should find what is missing if it is not there. It is best to repair any broken items. After everything has been checked, you can go outside to finish the job.